jactionscripters.com

Home > Error Codes > Whirlpool Duet Error Codes F 27

Whirlpool Duet Error Codes F 27

Contents

Check the water temperature sensor and connection to it. how do i check if the punps blocked? F26 DOOR SWITCH ERROR If the door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds. My advice for that would be a Mossberg 500. http://jactionscripters.com/error-codes/whirlpool-duet-washer-error-codes.php

This is bad... Replace Central Control Unit if drum is not moving. Replace heater. Look at the detergent container.

Kenmore F27 Error

I see that someone else asked a similar question. If too much detergent was used: – Run the unit through a RINSE/SPIN cycle. – Run a NORMAL cycle without adding any detergent. Check/clean drain pump filter of foreign objects. 5. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU).

  1. If no damage to wires and all connectors okay, proceed to step C.
  2. Check door switch contacts. 5.
  3. Replace User Interface if drum is rotating. 4.
  4. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1.
  5. Check wires and connectors from control to door switch, then from door switch to control.
  6. when i try to turn off the washer and restart it the same error comes up and the washer stops.

Open the lid or press STOP/CANCEL to clear the display. Check wires and connectors from control to latch switch, then from latch switch to control. Verify CCU operation by running a Diagnostic test or any cycle. E.

Check the MCU by looking for operations of the drive motor. 5. Replace door switch. Unplug washer or disconnect power. 8. Verify inlet valve operation.

Check if the hose is not blocked. Watch Queue Queue __count__/__total__ Find out whyClose Fix F-21 F-33 Whirlpool Duet Sport Drain Pump motor problems James Poag SubscribeSubscribedUnsubscribe8989 Loading... Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3. F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down.

Whirlpool 6th Sense Washing Machine Error Codes

Preview my answer Post my answer View Statistics: Past 24 Hours: 3 Past 7 Days: 23 Past 30 Days: 70 All Time: 1,121 22,368 Free Manuals 88,386 Solutions 6,703 Devices iFixit http://applianceassistant.com/Washer-Repair/Duet-Washer-2nd-Gen/Duet-Washer-Error-Codes.php F10 Motor Control Unit (MCU) heat sink thermal trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink Kenmore F27 Error All rights reserved. Whirlpool Front Load Washer Error Codes This error code may also be used if there is a disagreement between the motor and machine controllers on the state of the lid switch.

Plug in washer or reconnect power. 6. http://jactionscripters.com/error-codes/windows-sc-error-codes.php This code will also appear if the user presses the START key while the lid is open. Replace User Interface if drum is rotating. 4. NOTE: Detects by weight.

The failure will be reset after running the Diagnostic Test Program. 1. F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs. Check wire harness connections to the User Interface and the Central Control Unit. 3. this page Replace User Interface.

F3 - E1 Oven temperature sensor (RTD) shorted (upper oven, if double oven) F3 - E2 Oven temperature is too high (Cook mode) F3 - E3 Oven temperature is too high Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). I am about to use the dang thing for target practice!

Replace the Motor Control Unit.

Check the inlet valve for proper shut off. 7. F65 STEAMER TIME OUT REACHED Error happens if there is no communication between Central Control Unit (CCU) and steamer electronic board. Check the drive motor for powered rotations. 6. Transcript The interactive transcript could not be loaded.

George Vassallo 79,941 views 10:33 Washing Machine Repair - Replacing the Drain Pump (LG Part # 4681EA2001T) - Duration: 14:54. If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1. Measure door switch (door open = switch open small low voltage terminals). http://jactionscripters.com/error-codes/verisign-error-codes.php Duet Sport Washer Failure Code Condition Check/Repair F01 EEPROM ERROR A communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.

Verify CCU operation by running a Diagnostic Test or any cycle.