jactionscripters.com

Home > Socket Error > Windows Socket Error 10093

Windows Socket Error 10093

Contents

The only time a WinSock might use this error--at least with a TCP/IP implementation of WinSock--it fails a function with other errors (for example, WSAETIMEDOUT). Berkeley description: The protocol has not been configured into the system, or no implementation for it exists. WinSock functions: send(), sendto(), setsockopt() Additional functions: Any function that does network I/O: recv(), recvfrom(), FD_READ, FD_WRITE See also: WSAECONNABORTED, WSAECONNRESET, WSAETIMEDOUT WSAENETUNREACH (10051) Network is unreachable. Note: this error may also result if you try to send a multicast packet and the default gateway does not support multicast (check your interface configuration). this contact form

When I added a resistor to a set of christmas lights where I cut off bulbs, it gets hot. Chances are the network subsystem is misconfigured or inactive. You could also try to resolve another hostname you know should work, to check that the name resolution server application is running. Additional functions: With a datagram socket: send() or sendto(), or FD_READ. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx

Socket Error 10054

A retry at some time later may be successful. A function fails with WSAEAFNOSUPPORT if the address family referenced in sockaddr is not compatible with the referenced socket's protocol. How common is it to use the word 'bitch' for a female dog? Once we are happy that Winsock has initialized correctly, we can now use a handy function to address any further failures.

You would need to update your Winsock to a supported version. We took the text of the errno manual page in BSD 4.3, filled in gaps and embellished, completing the information. Berkeley description: A message sent on a socket was larger than the internal message buffer or some other network limit. Socket Error 10049 WinSock description: The 'address' it refers to is the remote socket name (protocol, port and address).

If you used a hostname, did it resolve to the correct address? Notice that asynchronous service and protocols functions are listed below, in addition to the hostname resolution functions. This is one of the most frequent errors and one of the best to encounter, since it's one of the least ambiguous. my response Great!

Berkeley description: This is a temporary condition and later calls to the same routine may complete normally (also known as EAGAIN error in Berkeley Software Distribution version 4.3) WinSock description: Same Socket Error 11004 If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. WSAEMSGSIZE 10040 Message too long. However, because a BSD socket is equivalent to a file handle, some Windows Sockets platforms provide some file handle and socket equivalency.

  1. Check that your network system (WinSock implementation) has a utility that shows network statistics.
  2. The socket input parameter is not a valid socket handle (either it never was valid, it's a file handle (not a socket handle), or if it was a socket handle, it
  3. This can help you (or your support staff) to zero-in on what's wrong when your application runs into a problem.
  4. WinSock description: a quick comparison to the Berkeley counterpart, and a long description of WinSock error.
  5. WinSock description: No equivalent.
  6. If you have more than one server configured, the hostname query fails only after the WinSock DLL has queried all servers.
  7. Of the two that can fail, neither of them set an error value you can retrieve from WSAGetLastError() (refer to Chapter 10, "Support Routines" for more information on any of these
  8. Developer suggestions: to make your application more portable: with datagram sockets don't use connect() and sendto() on the same datagram socket in an application, and always "disconnect" before calling connect() more
  9. For instance, this error will occur if you try to run two applications that have FTP servers.
  10. TCP/IP scenario: description of the TCP/IP protocol suite network traffic (i.e.

Socket Error Codes Linux

The WinSock implementation will not allow you to send after this. try here Berkeley description: An operation on a socket or pipe was not performed because the system lacked sufficient buffer space or because a queue was full. Socket Error 10054 I read online that this error caused by not calling WSAStartup() but I did called it in the socket's constructor and it did accept in the first time. Socket Error 10053 WSAEPROTOTYPE 10041 Protocol wrong type for socket.

Calls to WSAStartup() and WSACleanup() must be balanced at all times. weblink You should simply ignore this error when it occurs. WSAEMFILE 10024 Too many open files/sockets. Browse other questions tagged c++ sockets winsock or ask your own question. Socket Error 10054 Connection Reset By Peer

User suggestions: Some network systems have commands to report statistics. Most of the text comes from the output from the "man errno" command on Unix. WinSock description: The WinSock implementation cannot function at this time, because the underlying system it uses to provide network services is currently unavailable. http://jactionscripters.com/socket-error/winsock-10093-error.php WSAEWOULDBLOCK (10035) Operation would blockThis is a temporary condition and later calls to the same routine may complete normally.

WSAEADDRNOTAVAIL 10049 Cannot assign requested address. Windows Socket Error Windows 10 WSAECONNRESET (10054) Connection reset by peer A connection was forcibly closed by a peer. This is not a temporary error.

WSAENETDOWN (10050) Network is down A socket operation encountered a dead network.

Detailed description: setsockopt(): WinSock generates this error if you try to set SO_KEEPALIVE but the connection has already been aborted (e.g. WSANO_RECOVERY 11003 Non-recoverable error. In this case, it might be possible to check the count of TCP RST packets received, or ICMP Port Unreachable packets. Socket Error 10061 Connection Refused Typically, though, WinSock generates WSAENETUNREACH when it receives a "host unreachable" ICMP message from a router instead of WSAEHOSTUNREACH.

WinSock description: Same as Berkeley. Is there a technical term for this simple method of smoothing out a signal? See WSASYSNOTREADY for details. his comment is here to ->) the problem was successfully fixed.

Check your Winsock, protocol stack, network driver, and network interface card configuration. He also lurks around the forums as Hieran_Del8. WSAGetLastError() The next step was to set up a socket. Be aware that without Javascript, this website may not behave as expected.

WSADATA WsaDat; int nResult=WSAStartup(MAKEWORD(2,2),&WsaDat); if(nResult!=0) { std::cout<<"WSA Initialization failed: "<