jactionscripters.com

Home > Socket Error > Windows Winsock Error

Windows Winsock Error

Contents

Hello all I just wanted to know im using kana as e-mail and I just want to know if and when an e-mail comes will ... WSAEMSGSIZE 10040 Message too long. the byte-order functions, htonl(), htons(), ntohl and ntohl(), cannot fail. They signal unusual error conditions for which there's no WinSock error equivalent. weblink

marsmimar View Public Profile Find More Posts by marsmimar 12 Nov 2010 #4 Jacee Windows 7 Ultimate 32bit SP1 8,766 posts What Anti-virus software and Firewall are you ST3500630AS ATA Device. The v1.1 WinSock specification only ascribes thirty-three of the fifty errors to any of the WinSock functions in the v1.1 for Windows Sockets specification. Errors are listed in numerical order with the error macro name.

Socket Error 10054

WINSOCK Error: Protocol not supported.... For information, see the Handling Winsock Errors topic. WSAEINPROGRESS 10036 Operation now in progress. Because this error occurs during the program accesses the network, to solve this error you need to look at whether your network is functioning properly for Kana Dynamic IP Updater.

A socket operation was attempted to an unreachable network. Setup cannot load "inetstp.inf". Your site has been denied access to this server.... Socket Error 10053 If you have experience about the cause of your error that is not listed here, please tell your story by using contact page.

Ping a host on the same subnet as the host you were connected to (if you know one). Winsock Error Windows 7 Cannot load INETSTP.DLL. The content you requested has been removed. https://support.microsoft.com/en-us/kb/819124 It also occurs with functions that take a socket handle and a sockaddr structure as input parameters.

October 20th, 2008 by Aseem Kishore File in: Computer Tips There are 0 comments, care to add yours? Socket Error 10054 Connection Reset By Peer The behavior may vary: some WinSocks might complete in background, and others may require another call to closesocket to complete. send() & sendto(): socket not bound (for Dgram) or not yet connected (for Stream) The v1.1 specification also has a detailed description for the connect() function which says: "socket not already TCP/IP scenario: Calling shutdown() with how=1 or how=2 sends a TCP FIN packet to the remote address, which literally means "I'm done sending." If the local host sent any more data

Winsock Error Windows 7

The application has initiated an overlapped operation that cannot be completed immediately. https://technet.microsoft.com/en-us/library/cc975854.aspx somewhere in his 40's OS Windows 7 Ultimate 32bit SP1 CPU Intel(R) Core(TM)2 Quad CPU @ 2.40GHz, 2400 MHz Motherboard INTEL/D975XBX2 Memory 4 GB Graphics Card ATI Radeon HD 2600 Pro Socket Error 10054 WinSock description: Similar to Berkeley. Winsock Error 10061 User suggestions: Check that the WINSOCK.DLL file is in the current path Check that the WINSOCK.DLL file is from the same vendor as your underlying protocol stack.

WinSock description: No equivalent. have a peek at these guys WSASERVICE_NOT_FOUND 10108 Service not found. WinSock description: Same as Berkeley. The Windows Sockets API provides access to "low-level" API's (like the transport protocols TCP and UDP), so this error is not relevant to WinSock. Socket Error Codes Linux

  • Do a traceroute to try to determine where the failure occurs along the route between your host and the destination host.
  • Berkeley description: A required address was omitted from an operation on a socket.
  • It basically defines how two network programs will communicate with each other.
  • WinSock functions: socket() See also: WSAESOCKTNOSUPPORT WSAEPROTOTYPE (10041) Protocol wrong type for socket.
  • At this time (see the last update date below), the detail about the meaning of the error can be found from MSDN website.
  • An error with the underlying traffic control (TC) API as the generic QoS request was converted for local enforcement by the TC API.

According to AT&T repair center the latest firmware is installed on both modems (original and spare) as of Sep 2010 when I took the original modem in and purchased the spare. You’ll be auto redirected in 1 second. Developer suggestions: Did you close a socket inadvertently in one part of an application without keeping another part notified? check over here The following message should be seen: "Successfully reset the Winsock Catalog.

WinSock functions: accept(), bind(), closesocket(), connect(), gethostbyaddr(), gethostbyname(), gethostname(), getpeername(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), getsockname(), getsockopt(), ioctlsocket(), listen(), recv(), recvfrom(), select(), send(), sendto(), setsockopt(), shutdown(), socket(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), Socket Error 10049 Note that this error occurs rarely since a WinSock implementation cannot reliably detect hardware problems. Berkeley description: A write to an ordinary file, the creation of a directory or symbolic link, or the creation of a directory entry failed because the user's quota of disk blocks

Check that no old Windows Sockets DLL files are being accessed.

HTTP Server was unable to initialize due to a shortage of available memory.... The Windows Sockets implementation documentation to be sure all necessary components are currently installed and configured correctly. This error may also be returned for protocol and service queries, and means that the specified name could not be found in the relevant database. Socket Error 11004 The specified file handle is not a valid file-handle value or does not refer to an open file; or an attempt was made to write to a file or device opened

The Windows function is indicating a lack of required memory resources. Berkeley description: A socket operation encountered a dead network. This usually results from trying to connect to a service that is inactive on the foreign host. this content WINSOCK Error: Software caused connection abort....

WSAEPROTONOSUPPORT 10043 Protocol not supported. connect(), send(), recv(), et cetera).