WSAENOTCONN 10057 Socket is not connected. For example, this error is returned if sendto is called with the remote address of ADDR_ANY. But most of these function-less errors are simply out of place; they are inappropriate to the Windows Sockets API as it exists in the v1.1 specification. WSA_OPERATION_ABORTED 995 Overlapped operation aborted. news
Berkeley description: A directory with entries other than `.'and `..' was supplied to a remove directory or rename call. User suggestions: Check the obvious first: check that the destination address is a valid IP address. Either the application has not called WSAStartup or WSAStartup failed. Blocking on outbound connections is not typically done in Firewalls because then basically nothing would work.
Additional functions: a generic description of the type of functions that can return this error, which may include functions other than those listed by the WinSock specification. User suggestions: There are a number of things to check, that might help to identify why the failure occurred. A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using sendto) no address was supplied. when i stopped the process(had to do it like three times before it stopped just running again) the internet and outlook express both worked fine.
However, some WinSocks fail with WSAEINVAL you call connect() a second time (or subsequent) on a non-blocking socket. WSAEBADF 10009 File handle is not valid. Verify that your subnet mask is setup properly. Winsock Error 10060 User suggestions: Check that the WINSOCK.DLL file is in the current path Check that the WINSOCK.DLL file is from the same vendor as your underlying protocol stack.
If you continue to receive the same error after insuring ports 20 and 21 are open, contact the administrator of the site you are trying to connect to. WSA_QOS_EPOLICYOBJ 11025 Invalid QoS policy object. This normally results from an attempt to bind to an address that is not valid for the local computer. http://support.dameware.com/kb/article.aspx?ID=300060 If so,verifyif you have anything on your network that could be filtering or tampering with these SMTP out sessions, such as third party AntiVirus software installed on the MDaemon server or
connect(), send(), recv(), et cetera). Socket Error 10061 Connection Refused WSA_QOS_GENERIC_ERROR 11015 QoS generic error. WSAENOPROTOOPT (10042) Bad protocol option. Generically, the error means the network system has run out of socket handles.
WinSock description: Same as Berkeley. Winsock errors are always network related errors. What Is A Socket Error WinSock only allows a single blocking operation to be outstanding per task (or thread), and if you make any other function call (whether or not it references that or any other Socket Error Codes Linux The requested service provider is invalid.
Windows Sockets only allows a single blocking operation—per- task or thread—to be outstanding, and if any other function call is made (whether or not it references that or any other socket) http://jactionscripters.com/socket-error/winsock-error-997.php Basically, you want to identify where the problem occurred. Note: this error may also result if you are trying to send a multicast packet and the default gateway does not support multicast (check your interface configuration). The requested service provider could not be loaded or initialized. Socket Error 10054 Connection Reset By Peer
If there is more than one Winsock DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. Developer suggestion: are you trying to use an optional feature? An MX record is returned but no A record—indicating the host itself exists, but is not directly reachable. More about the author Are they both interchangable?
Unfortunately, sending emails to a slow server (only one for now) throws always error 10060: Fri 2014-09-26 15:33:24: Attempting SMTP connection to [212.239.##.77:25] Fri 2014-09-26 15:33:24: Waiting for socket connection... Socket Error 11004 WinSock functions: WSAEUSERS (10068) Too many users. And what is the purpose of "Wait xx seconds for sockets to connect before giving up" setting, then? Note that this error is returned by the operating system, so the error number may change in future releases of Windows.
The timeout will occur after approximately 21 seconds (3+6+12). The WSAGetLastError function returns the last error that occurred for the calling thread. Alt-N staff members may participate in the forums periodically but please recognize that this is not the official method of receiving technical support. Socket Error 10061 Ppsspp This usually means the local software knows no route to reach the remote host.
WSAENETRESET (10052) Network dropped connection on reset. These configuration issues then cause the TCP Socket to timeout, which then causes the Winsock 10060 error to occur. WSANO_RECOVERY 11003 This is a nonrecoverable error. click site The requested protocol has not been configured into the system, or no implementation for it exists.
So, for example, if a WinSock implementation doesn't support SOCK_RAW with IPPROTO_IP (or any other protocol), then the socket() call would fail with WSAEPROTONOSUPPORT (however, if it doesn't support SOCK_RAW at WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), See also: WSAHOST_NOT_FOUND, WSANO_RECOVERY, WSATRY_AGAIN WSANO_RECOVERY (11003) This is a non-recoverable error Berkeley description: This is a WSAESHUTDOWN 10058 Cannot send after socket shutdown. Alternately, you could call getprotobyname() or WSAAsyncGetProtoByName() to get the appropriate protocol value from the network system.
The address manipulation functions, inet_ntoa() andinet_addr(), can fail. Hi, my MDaemon email server is working very fine with version 13.6. The error can occur when the local network system aborts a connection. Monkey530 Video Card Support 36 07-19-2005 02:48 AM Posting Rules You may not post new threads You may not post replies You may not post attachments You may not edit your
WinSock functions: accept(), bind(), getsockname(), ioctlsocket(), listen(), recv(), recvfrom(), select(), send(), setsockopt(), shutdown(), WSAStartup(), WSAAsyncSelect(), WSACancelAsyncRequest(), WSACancelBlockingCall, FD_CONNECT Additional functions: Any WinSock function that takes input parameters that could be invalid Check whether you have a router configured in your network system (your WinSock implementation). For inet_addr(), this could mean the content of the buffer passed or the buffer itself is invalid. Outgoing connections can be affected by the presence of firewall or anti-virus software on the local computer or network connection.
WinSock functions: WSAESHUTDOWN (10058) Cannot send after socket shutdown. An invalid shaping rate object was found in the QoS provider-specific buffer. Developer suggestion: The simple suggestion is "don't do that." No matter what value you use for the "how" parameter to the shutdown() function, you cannot send afterwards. For instance, you might get WSAEBADF in place of WSAENOTSOCK on a system that provides some socket and file handle equivalency.
WSAEADDRINUSE 10048 Address already in use. WinSock functions: connect(), sendto(), FD_CONNECT WSAEDQUOT (10069) Disc quota exceeded. Our software is compatible with any firewall (hardware or software), but you must properly configure the firewall to allow the necessary traffic to pass through. If so, then the application might have had a problem resolving the name (see suggestions at WSATRY_AGAIN for more information).
© Copyright 2017 jactionscripters.com. All rights reserved.