jactionscripters.com

Home > Socket Error > Winsock Socket Error=10022

Winsock Socket Error=10022

Contents

TCP/IP scenario: Calling shutdown() with how=1 or how=2 sends a TCP FIN packet to the remote address, which literally means "I'm done sending." If the local host sent any more data WinSock description: Unlike Berkeley Sockets, in WinSock WSAEALREADY means that the asynchronous operation you attempted to cancel has already been canceled. User suggestions: Did you enter a destination hostname? WSAEISCONN 10056 Socket is already connected. news

There are only a few possible causes for this error: you tried to connect to the wrong port. Reply With Quote February 18th, 2009,03:30 AM #2 scorrpeio View Profile View Forum Posts Member Join Date Dec 2008 Posts 86 Re: Socket Error 10022 Guys, I came to realise that If you are using a name server(s), check whether the server host(s) are up (e.g. A socket operation encountered a dead host. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx

Socket Error 10054

For instance, even if you request to send() a few bytes of data on a newly created TCP connection, send() could fail with WSAEWOULDBLOCK (if, say, the network system has a Berkeley description: A socket operation was attempted to an unreachable network. Since Windows Sockets is practically a clone of Berkeley Sockets, and the rule of thumb is "when in doubt, defer to Berkeley", we can adopt the Berkeley Software Distribution error text

  1. At least one QoS send path has arrived.
  2. The item is not available locally.
  3. A QoS error occurred due to lack of resources.

WSA Information: high ver: 2.2 ver: 2.2 desc: WinSock 2.0 stat: Running max sock: 0 max udp size: 0 socket failed : err: 10022 An invalid argument was supplied. Besides, you have to check the RecvSocket value returned by socket(...) to be NOT the INVALID_SOCKET. Victor Nijegorodov Reply With Quote February 18th, 2009,06:46 AM #4 scorrpeio View Profile View It is also possible that WinSock might return this error after an application calls connect() a second time on a non-blocking socket while the connection is pending (i.e. Socket Error 10049 A general QoS error.

WinSock description: Almost same as Berkeley. Socket Error Codes Linux Alternately, you could call getprotobyname() or WSAAsyncGetProtoByName() to get the appropriate protocol value from the network system. Although the specification doesn't list an error for a function, it does allow for it. Go Here Generically, the error means the network system has run out of socket handles.

WinSock functions: the list of functions that explicitly list this error in the v1.1 Windows Sockets specification. Socket Error 11004 WinSock functions: accept(), bind(), getsockname(), ioctlsocket(), listen(), recv(), recvfrom(), select(), send(), setsockopt(), shutdown(), WSAStartup(), WSAAsyncSelect(), WSACancelAsyncRequest(), WSACancelBlockingCall, FD_CONNECT Additional functions: Any WinSock function that takes input parameters that could be invalid Here's the "call stack" socket() WSPSocket() SockSocket() The function call that fails is NtCreateFile. The Windows function is indicating a problem with one or more parameters.

Socket Error Codes Linux

All sockets are created with an associated address family (that is, AF_INET for Internet Protocols) and a generic protocol type (that is, SOCK_STREAM). http://stackoverflow.com/questions/25966536/winsock-error-10022-on-listen-when-include-thread This message has a slightly different meaning from WSAEAFNOSUPPORT. Socket Error 10054 WinSock description: NOT same as Berkeley, but analogous. Socket Error 10053 There are no QoS senders.

User suggestions: There are a number of things to check, that might help to identify why the failure occurred. navigate to this website On a datastream socket, some applications use this error with a non-blocking socket calling connect() to detect when a connection attempt has completed, although this is not recommended since some WinSocks Developer suggestions: Since there're only one corresponding protocol for each of the datagram and datastream socket types in the Internet address family, you should simply leave the value in the protocol Not implemented: name server does not perform specified operation. Socket Error 10054 Connection Reset By Peer

WSAEPROTONOSUPPORT (10043) Protocol not supported. Developer suggestions: Chances are, that if you encounter this error, your application ignored the failure of some previous function. Note that the v1.1 WinSock specification does not explicitly state that this error occurs if the value you request is larger than the WSAData.iMaxUdpDg returned from WSAStartup(). More about the author The service provider procedure call table is invalid.

An application used a Windows Sockets function which directly maps to a Windows function. Winsock Error 10054 Fix TCP/IP scenario: Most WinSock implementations use domain name system (DNS) protocol for hostname to address resolution, although a few use Network Information System (NIS). Exiting...."); exit(1); } //Create the server socket if((serverSocket = socket(AF_INET,SOCK_STREAM,0))==INVALID_SOCKET) throw "can't initialize socket"; //Fill-in Server Port and Address info.

A system call that should never fail has failed.

These errors might be reported on any function that does network I/O (e.g. Tuesday, January 22, 2013 5:30 PM Reply | Quote 2 Sign in to vote FINALY I got the fix for this problem. WSA Information: high ver: 2.2 ver: 2.2 desc: WinSock 2.0 stat: Running max sock: 0 max udp size: 0 socket succeeded : 68 When run from a certain network share: Socket Error 10061 Connection Refused User suggestions: Some network systems have commands to report statistics.

Hi Andy. This error may also be returned for protocol and service queries, and means that the specified name could not be found in the relevant database. That will fill the output addrinfo with data that is suitable to pass to bind(). click site BUT stangely enough EVERYTHING works on my LAPTOP - why the difference ??????

Is the router up and running (check by pinging it, and then ping an address on the other side of it)? SO_ACCEPTCONN, SO_ERROR, SO_TYPE: are read-only options, so they work with getsockopt(), but not with setsockopt() Developer suggestions: Check the parameters. This can help you (or your support staff) to zero-in on what's wrong when your application runs into a problem. WSA_QOS_EFLOWSPEC 11017 QoS flowspec error.

Alternately, you can get the local IP address by calling gethostname() followed by gethostbyname(). This usually means the local software knows no route to reach the remote host. WinSock functions: send(), sendto(), setsockopt() Additional functions: Any function that does network I/O: recv(), recvfrom(), FD_READ, FD_WRITE See also: WSAECONNABORTED, WSAECONNRESET, WSAETIMEDOUT WSAENETUNREACH (10051) Network is unreachable. Performing cleanup..."); WSACleanup(); } int main(void){ initializeSockets(); return 0; } I have read the thread Winsock Error 10022 on Listen but I don't think that this has solution to my problem.

Once I include the thread class the program fails on listen and gives a 10022 error. (I haven't done anything related to threads yet, only import). However, there's little distinction between WSAEALREADY and WSAEINVAL since a WinSock DLL cannot tell the difference between an asynchronous operation that has been cancelled and one that was never valid. The file handle supplied is not valid. WSAEADDRNOTAVAIL 10049 Cannot assign requested address.

Berkeley description: A request to send data was disallowed because the socket had already been shut down with a previous shutdown() call.